BOYSEN Flatwall Enamel B‑800

BOYSEN®® Flatwall Enamel B‑800

BOYSEN®® Flatwall Enamel is a flat, alkyd-type paint that is both durable and fast-drying. It is formulated to give a tough and beautiful finish on wood and metal. Because of its superior hiding properties, it can also be used as a primer for enamel coatings. It levels evenly and shows no lap and brush marks when applied skillfully.

Technical Data

Principal Uses

It is ideal for interior and exterior wood and metal surfaces.

Vehicle Type

Alkyd Resin

Finish

Flat

Dry Time

Touch: 1 hour
Recoat: 2 hours
Full cure: 8 hours
*Measured at 25°C and 50% relative humidity

Density
(±0.05 kg/L)

1.52 kg/L

Theoretical Coverage

25-30 sq. m.
* per 4-Liters at 2.5-2.0 mils DFT
*Depending on surface texture and porosity

Tinting

Will accept BOYSEN®® Oil Tinting Colors at a maximum level of ¼ Liter per 4-Liter can. Take note that B‑2319 Hansa Yellow and B‑2315 Bulletin Red are for interior painting only.

Thinning
Solvent

Thin with not more than 1-Liter of BOYSEN®® Paint Thinner B‑0340 per 4-Liter can of BOYSEN®® alkyd enamel products.

Clean-up
Solvent

BOYSEN®® Paint Thinner B‑0340

Packaging

1-Liter, 4-Liters, and 16-Liters

Application

By brush or roller

SURFACE PREPARATION

Wooden Surfaces

Surface to be painted should be clean and dry, free from dust, dirt, and other foreign matter. Hammer all nails deep enough to apply putty. Sand rough wood until smooth and then dust off before painting.
For repainting, scrape off all loose, scaling, flaking, and peeling paint manually or by using BOYSEN®® Paint and Varnish Remover B‑141, as necessary. Wash surfaces clean and completely remove chemical residue. Let it dry. Prime with BOYSEN®® Flatwall Enamel B‑800 before recoating.

Metal Surfaces

Wipe the surface with a rag soaked in paint thinner to remove grease, oil, wax and other foreign matter. For new galvanized surfaces, etch the surface by applying 10% BOYSEN®® Metal Etching Solution B‑71 (Dilute 1 part of B‑71 to 9 parts water). Rinse with water and dry immediately.
Unpainted galvanized surfaces that have been exposed for 6 months or more need not be etched.
For recoating pre-painted galvanized surfaces in good condition, sand lightly then wipe the surface with a clean rag before applying paint. Remove all loose paint film to sound surface. Spot prime bare substrate.
For corroded galvanized surfaces, remove rust by wire brushing and use BOYSEN®® Metal Etching Solution B‑71. Let it stay for 10-15 minutes. Be sure to remove all remaining residue. Immediately prime after drying.

PAINTING SCHEDULE

Wooden Surfaces

Primer:
BOYSEN®® Flatwall Enamel B‑800
Putty:
BOYSEN®® Plasolux Glazing Putty B‑311
2nd & 3rd coat:
BOYSEN®® Flatwall Enamel B‑800

Metal Surfaces

Primer:
BOYSEN®® Red Oxide Metal Primer B‑310
2nd & 3rd coat:
BOYSEN®® Flatwall Enamel B‑800

Colors

White
* May be tinted to pastel or light shades using BOYSEN®® Oil Tinting Colors.
* Also available in B‑691 Flat Black.
* For technical reasons connected with color reproduction in print and paint manufacturing, these colors may not exactly match actual paint color.
For MSDS requests, please email technical@boysen.com.ph