BOYSEN® Acrytex™

BOYSEN® Acrytex™

DESCRIPTION: BOYSEN® Acrytex™ is an acrylic solvent-based coating that forms a seamless, non-porous, watertight film that repels water and prevents seepage. It is noted for its excellent adhesion and long-term durability. Creates a very tight film, serving as a moisture sealant for concrete and a stain inhibitor for wood.

PRINCIPAL USES: As topcoat for new and previously painted interior and exterior masonry and wooden surfaces

FINISH: Flat, Semi-Gloss and Gloss

DRY TIME:
Touch: 30 minutes
Recoat: 2 hours

THEORETICAL COVERAGE PER 4-LITERS: 
Plain finish: 25 - 30 sq. m.
Textured finish: 15 - 18 sq. m.
*Depending on surface texture and porosity

TINTING: Use Acrytex™ Tinting Colors at a ratio of 1:16, colorant to paint

THINNING SOLVENT: BOYSEN® Acrytex™ Reducer B-1750
*If using brush or roller, use approximately 1-Liter of Acrytex™  Reducer B-1750 per 4-Liter of Acrytex™ paint.

CLEAN-UP SOLVENT: 
BOYSEN® Acrytex™ Reducer B-1750

PACKAGING: 4-Liters and 16-Liters

APPLICATION: By brush, roller or spray

DESCRIPTION: BOYSEN® Acrytex™ is an acrylic solvent-based coating that forms a seamless, non-porous, watertight film that repels water and prevents seepage. It is noted for its excellent adhesion and long-term durability. Creates a very tight film, serving as a moisture sealant for concrete and a stain inhibitor for wood.

PRINCIPAL USES: As topcoat for new and previously painted interior and exterior masonry and wooden surfaces

FINISH: Flat, Semi-Gloss and Gloss

DRY TIME:
Touch: 30 minutes
Recoat: 2 hours

THEORETICAL COVERAGE PER 4-LITERS: 
Plain finish: 25 - 30 sq. m.
Textured finish: 15 - 18 sq. m.
*Depending on surface texture and porosity

TINTING: Use Acrytex™ Tinting Colors at a ratio of 1:16, colorant to paint

THINNING SOLVENT: BOYSEN® Acrytex™ Reducer B-1750
*If using brush or roller, use approximately 1-Liter of Acrytex™  Reducer B-1750 per 4-Liter of Acrytex™ paint.

CLEAN-UP SOLVENT: 
BOYSEN® Acrytex™ Reducer B-1750

PACKAGING: 4-Liters and 16-Liters

APPLICATION: By brush, roller or spray

SURFACE PREPARATION:
New Concrete

Allow new concrete to dry for 14-28 days under normal weather conditions before painting. Surface to be painted should be clean and dry, free from oil, grease, dust, dirt, contaminants, and all loose grit and mortar.

Wooden Surfaces
Surface to be painted should be clean and dry, free from dust, dirt, and other foreign matter. Hammer all nails deep enough to apply putty. Sand rough wood until smooth and then dust off before painting.

Repainting
Any existing paint that is not Acrytex™ should be completely removed. Scrape off all loose, scaling, flaking, and peeling paint as necessary. Make sure the surface is clean, dry, and good weather persists prior to painting.

For repainting concrete, use BOYSEN® Chalk Blocker™ B-7304 as surface conditioner if surface is chalky. In case of mildew infestation, treat with a bleach solution (1:3, laundry bleach to water, respectively) by swabbing or brushing. To ensure proper treatment, let stand for 24 hours before cleaning off residue. Let dry.


PAINTING SCHEDULE:

Plain Finish
1. Prime bare substrate with BOYSEN® Acrytex™ Primer B-1705
2. Putty minor surface imperfections with BOYSEN® Acrytex™ Cast B-1711
3. Spot prime puttied areas with BOYSEN® Acrytex™ Primer B-1705
4. Finish with at least 2 coats of BOYSEN® Acrytex™ Topcoat to desired sheen

Textured Finish
1. Prime bare substrate with BOYSEN® Acrytex™ Primer B-1705
2. Spray BOYSEN® Acrytex™ Cast B-1711 using a mortar gun. For a flattened texture, press  Acrytex™ Cast B-1711 using a plain wooden roller 10-15 minutes after spraying.
Note: Dampen wooden roller with water to prevent the roller from sticking to the cast.
3. Finish with at least 2 coats of BOYSEN® Acrytex™ Topcoat to desired sheen