Concrete
Interior: Decorative
and Special Finishes
New

BOYSEN®® DECORe™
Classic

Concrete
Interior: Decorative
and Special Finishes
New

BOYSEN®® DECORe™
Classic

BOYSEN®® DECORe™ Classic

BOYSEN®® DECORe™ Classic is a unique, water-based decorative paint system that can simulate the complex texture and distinctive finish of the European masters right in your home. Unlike traditional faux finishes, BOYSEN®® DECORe™ Classic does not need elaborate intermixing of colors, layering techniques or sophisticated equipment. Simple and effortless brushing is all that's required to achieve this very exquisite finish.

Download Brochure

SURFACE PREPARATION

Allow new concrete to dry for 14-28 days under normal weather conditions before painting.

Surface to be painted should be clean and dry, free from oil, grease, dust, dirt, contaminants, and all loose grit and mortar.

If neutralizing, treat surface with a solution of 1 part BOYSEN®® Masonry Neutralizer B‑44 diluted in 16 parts water, applying liberally by brush or roller. Let dry overnight before rinsing with water to remove white crystals that form on the surface. Let dry before painting.

Note: If the concrete has been cured for more than 28 days, there is no need for neutralizer.

PAINTING SCHEDULE

Prime bare concrete with BOYSEN®® Permacoat™ Flat Latex B‑701.

Fully cover the entire surface using BOYSEN®® DECORe™ Undercoat B‑4605 by brush or roller. Let dry for 1 hour before applying the succeeding layer.

Mix BOYSEN®® DECORe™ Toner into BOYSEN®® DECORe™ Base B‑4610. A color can be applied in different tones by varying amount of toner used, either Full, One-half, One- Fourth, or any other proportion depending on desired shade. Stir until uniform consistency is achieved.

Using a BOYSEN®® DECORe™ brush, apply the prepared BOYSEN®® DECORe™ Base with Toner starting from top corner, working with short crisscrossing strokes. Brush through surface while the paint is still wet to achieve a more uniform pattern.

Wait for 8-10 minutes after applying BOYSEN®® DECORe™. Then, lightly comb the surface using the plastic scraper with long crisscrossing strokes, the scraper inclined and close to the surface.

NOTES

Do not thin mixture with water or any solvent.

Designs can only be achieved using BOYSEN®® DECORe™ Undercoat.

Only use the provided BOYSEN®® DECORe™ Brush and Scraper. The desired finish may not be achieved if a different material is used.

Colors

B‑4730

Light Gray

1 Toner

1/2 Toner

1/4 Toner

B‑4741

Aqua Blue

1 Toner

1/2 Toner

1/4 Toner

B‑4742

Light Blue

1 Toner

1/2 Toner

1/4 Toner

B‑4743

Deep Blue

1 Toner

1/2 Toner

1/4 Toner

B‑4750

Dark Green

1 Toner

1/2 Toner

1/4 Toner

B‑4762

Medium Yellow

1 Toner

1/2 Toner

1/4 Toner

B‑4763

Bright Yellow

1 Toner

1/2 Toner

1/4 Toner

B‑4771

Soft Red

1 Toner

1/2 Toner

1/4 Toner

B‑4772

Brick Red

1 Toner

1/2 Toner

1/4 Toner

B‑4780

Brown

1 Toner

1/2 Toner

1/4 Toner

* For technical reasons connected with color reproduction in print and paint manufacturing, these colors may not exactly match actual paint color.

Paintable Surface Area

SQM

Paint System	Product	Quantity
Primer	BOYSEN®® Permacoat™ Latex Flat Latex B‑701	5	L
Putty (Spot)	BOYSEN®® Masonry Putty B‑7311	5	L
or Putty (Full)	BOYSEN®® Masonry Putty B‑7311	12	L
Undercoat	BOYSEN®® DECORe™ Classic Undercoat B‑4605	10	L
Basecoat	BOYSEN®® DECORe™ Classic Base B‑4610	5	L
Toner (Full-Tone)	BOYSEN®® DECORe™ Classic Toner	240	mL

* Quantity shown will only be an estimate

1 Gallon = 4 Liters

Want to try again with a different set of selections?

Start over with the button below

Start Over

For MSDS requests, please email technical@boysen.com.ph